ACB 3645 5062 SS - 1.8 inch 440C stainless steel Angular Contact Headset Bearing (50mm 62mm x 8mm: 36 x 45 deg) -Angular-contact headset bearing featuring 440C stainless steel balls and races for superior corrosion protection.This oversized size bearing is also known as TH MR229, and has been specified on the Giant Reign e+ series bikes.Not all stainless steel is created equal.Enduro only uses 440C stainless steel balls and races to provide long life and superior corrosion resistance in applications and environments that may be less than ideal. 440C has the highest strength, hardness, and wear resistance of all the standard 440-series stainless alloys with high carbon content. As expected, it is also the most expensive of the 440 series alloys and requires multiple rounds of heat treatment and cryogenic treatments to achieve its superior mechanical properties. Though stainless steel has 20% less load capacity and is slightly softer than our standard 52100 chromium steel used in most of our bearings, stainless steel is an excellent alternative for use in wet conditions, if you wash your bike often, or where sweat can be a problem. Enduro Bearings also uses LLB type seals and CRC Marine Grease in these bearings to additionally water proof against the elements. Enduro 440C stainless headset bearings are the same bearings found in many popular headset brands, including those that carry a 110 year warranty.The Enduro line of headset bearings begin with chromium steel, Black Oxide finish A/C type and then offer full 440C stainless steel at the top. They are always engineered with the largest balls possible and dual lip seals riding in a micro-groove for ultimate protection against sweat and the elements. They are filled 90% with high pressure water proof grease, so you never have to guess if there is grease inside. Enduro angular Contact (A/C) bearings, all balls are engaged to spread the force over a larger surface area, pressure water and minimizing wear.
Static load - 935lbf / 4.15kN
Weight - 20g
ACB 4545 4252 SS - 1-1/2 440C stainless steel Angular Contact Headset bearing (42mm x 52mm x 7mm; 45 x 45deg) - Angular-contact headset bearing featuring 440C stainless steel balls and races for superior corrosion protection.This size bearing has been used as an upper bearing for Acros headsets that are designed specifically for aero cable routing, and is also know by part number AC4252Not all stainless steel is created equal.Enduro only uses 440C stainless steel balls and races to provide long life and superior corrosion resistance in applications and environments that may be less than ideal. 440C has the highest strength, hardness, and wear resistance of all the standard 440-series stainless alloys with high carbon content. As expected, it is also the most expensive of the 440 series alloys and requires multiple rounds of heat treatment and cryogenic treatments to achieve its superior mechanical properties. Though stainless steel has 20% less load capacity and is slightly softer than our standard 52100 chromium steel used in most of our bearings, stainless steel is an excellent alternative for use in wet conditions, if you wash your bike often, or where sweat can be a problem. Enduro Bearings also uses LLB type seals and CRC Marine Grease in these bearings to additionally water proof against the elements. Enduro 440C stainless headset bearings are the same bearings found in many popular headset brands, including those that carry a 110 year warranty.The Enduro line of angular-contact headset bearings start with Black Oxide treated Chromium Steel races, steps up to full 440C stainless steel, and the top of the line is, lifetime-guaranteed, XD-15 aerospace-stainless (races and balls). They are always engineered with the largest balls possible, feature dual-lip seals riding in a micro-groove (labyrinth) and are filled 90% with high pressure water proof grease for the ultimate protection against sweat and the elements. Enduro Angular Contact (A/C) bearings are designed so all balls are evenly engaged to spread the force over a larger surface area, decreasing friction, minimizing wear and maximizing life.
Static load - 917lbf / 408kN
Weight - 24.9g
A headset designed to bridge the gap between the 40-series and 110-series headsets. With all the design characteristics, sealing element, and Hellbender bearing found on a 110-series headset, at a price closer to a 40-series.
Machined from 6061 T-6 aluminium
Alloy dual seal crown race
Premium Hellbender bearings with low-friction seals
Interlok spacer compatible
Internal parts are cross compatible across the 10, 40 and 110-series
Upper stack: 9mm (Short)Â
Lower stack: 1mmÂ
Weight: TBC
Warranty: 1 Year (excluding bearings)
A headset designed to bridge the gap between the 40-series and 110-series headsets. With all the design characteristics, sealing element, and Hellbender bearing found on a 110-series headset, at a price closer to a 40-series.
Machined from 6061 T-6 aluminium
Alloy dual seal crown race
Premium Hellbender bearings with low-friction seals
Interlok spacer compatible
Internal parts are cross compatible across the 10, 40 and 110-series
Upper stack: 9mm (Short)Â
Lower stack: 1mmÂ
Weight: TBC
Warranty: 1 Year (excluding bearings)
ACB 6806 CC SS- 1-3/8"" 440C stainless steel Angular Contact Headset bearing (37mm x 49mm x 6.5mm; 36 x 45deg)Angular-contact headset bearing featuring 440C stainless steel balls and races for superior corrosion protection.This size bearing is also known in the bike Industry by part number HD446K.Not all stainless steel is created equal.Enduro only uses 440C stainless steel balls and races to provide long life and superior corrosion resistance in applications and environments that may be less than ideal. 440C has the highest strength, hardness, and wear resistance of all the standard 440-series stainless alloys with high carbon content. As expected, it is also the most expensive of the 440 series alloys and requires multiple rounds of heat treatment and cryogenic treatments to achieve its superior mechanical properties. Though stainless steel has 20% less load capacity and is slightly softer than our standard 52100 chromium steel used in most of our bearings, stainless steel is an excellent alternative for use in wet conditions, if you wash your bike often, or where sweat can be a problem. Enduro Bearings also uses LLB type seals and CRC Marine Grease in these bearings to additionally water proof against the elements. Enduro 440C stainless headset bearings are the same bearings found in many popular headset brands, including those that carry a 110 year warranty.The Enduro line of angular-contact headset bearings start with Black Oxide treated Chromium Steel races, steps up to full 440C stainless steel, and the top of the line is, lifetime-guaranteed, XD15 aerospace-stainless (races and balls). They are always engineered with the largest balls possible, feature dual-lip seals riding in a micro-groove (labyrinth) and are filled 90% with high pressure water proof grease for the ultimate protection against sweat and the elements. Enduro Angular Contact (A/C) bearings are designed so all balls are evenly engaged to spread the force over a larger surface area, decreasing friction, minimizing wear and maximizing life.
Static load - 917lbf / 408kN
Weight - 24.9g"
Precision, quality, valueHellbender 70 Lite is a headset that packs durability, weight savings and value into one product. Equipped with 6000 series aluminum and 35% lighter over comparable models. The Hellbender 70 Lite is an ideal headset choice for any bike where weight savings is a priority - a lightweight headset that doesn’t lack durability or performance.
CUPS & COVERS: 6061 T-6 Aluminum Internally contoured and relieved to minimize weight and maximize strength
TOP COVER: Low-friction upper bearing seal completely seals cup from contaminants and is fully captured by the top cover with no loose parts
CROWN RACE: Alloy Dual-Seal crown race provides excellent seal efficiency
COMPRESSION RING:Â Low friction Carbon friendly captured compression ring
BEARINGS: Lightweight aluminum/w steel hybrid Hellbender LITE sealed cartridge bearing
WEIGHT: ZeroStack (ZS) — 90g (vs 117g for normal ZS Hellbender) Integrated (IS) — 54g (vs 81g for normal IS Hellbender)
Precision, quality, valueHellbender 70 Lite is a headset that packs durability, weight savings and value into one product. Equipped with 6000 series aluminum and 35% lighter over comparable models. The Hellbender 70 Lite is an ideal headset choice for any bike where weight savings is a priority - a lightweight headset that doesn’t lack durability or performance.
CUPS & COVERS: 6061 T-6 Aluminum Internally contoured and relieved to minimize weight and maximize strength
TOP COVER: Low-friction upper bearing seal completely seals cup from contaminants and is fully captured by the top cover with no loose parts
CROWN RACE: Alloy Dual-Seal crown race provides excellent seal efficiency
COMPRESSION RING:Â Low friction Carbon friendly captured compression ring
BEARINGS: Lightweight aluminum/w steel hybrid Hellbender LITE sealed cartridge bearing
WEIGHT: ZeroStack (ZS) — 90g (vs 117g for normal ZS Hellbender) Integrated (IS) — 54g (vs 81g for normal IS Hellbender)
Precision, quality, valueHellbender 70 Lite is a headset that packs durability, weight savings and value into one product. Equipped with 6000 series aluminum and 35% lighter over comparable models. The Hellbender 70 Lite is an ideal headset choice for any bike where weight savings is a priority - a lightweight headset that doesn’t lack durability or performance.
CUPS & COVERS: 6061 T-6 Aluminum Internally contoured and relieved to minimize weight and maximize strength
TOP COVER: Low-friction upper bearing seal completely seals cup from contaminants and is fully captured by the top cover with no loose parts
CROWN RACE: Alloy Dual-Seal crown race provides excellent seal efficiency
COMPRESSION RING:Â Low friction Carbon friendly captured compression ring
BEARINGS: Lightweight aluminum/w steel hybrid Hellbender LITE sealed cartridge bearing
WEIGHT: ZeroStack (ZS) — 90g (vs 117g for normal ZS Hellbender) Integrated (IS) — 54g (vs 81g for normal IS Hellbender)
Featuring some of the lowest stack height bearing cover options available, our premium stainless steel Hellbender bearing, 6061 T-6 Aluminum cups and covers, the Hellbender 70 Slam is a premium headset created for riders seeking to lower their handlebars as low as possible without compromising bearing longevity and proper preload.
CUPS & COVERS: 6061 T-6 Aluminum Internally contoured and relieved to minimize weight and maximize strength
TOP COVER: Designed with the lowest stack height possible for both ZS and IS headsets
CROWN RACE: Alloy Dual-Seal crown race provides excellent seal efficiency
COMPRESSION RING:Â Low friction Carbon friendly captured compression ring
BEARINGS: Premium sealed HELLBENDER stainless bearings
STACK HEIGHT: ZS - 2mm top (vs 8mm top for normal ZS Hellbender) IS - 4.6mm top (vs 9mm top for normal ZS Hellbender)
Featuring some of the lowest stack height bearing cover options available, our premium stainless steel Hellbender bearing, 6061 T-6 Aluminum cups and covers, the Hellbender 70 Slam is a premium headset created for riders seeking to lower their handlebars as low as possible without compromising bearing longevity and proper preload.
CUPS & COVERS: 6061 T-6 Aluminum Internally contoured and relieved to minimize weight and maximize strength
TOP COVER: Designed with the lowest stack height possible for both ZS and IS headsets
CROWN RACE: Alloy Dual-Seal crown race provides excellent seal efficiency
COMPRESSION RING:Â Low friction Carbon friendly captured compression ring
BEARINGS: Premium sealed HELLBENDER stainless bearings
STACK HEIGHT: ZS - 2mm top (vs 8mm top for normal ZS Hellbender) IS - 4.6mm top (vs 9mm top for normal ZS Hellbender)
Not all stainless steel is created equal.Enduro only uses 440C stainless steel balls and races to provide long life and superior corrosion resistance in applications and environments that may be less than ideal. 440C has the highest strength, hardness, and wear resistance of all the standard 440-series stainless alloys with high carbon content. As expected, it is also the most expensive of the 440 series alloys and requires multiple rounds of heat treatment and cryogenic treatment to achieve its superior mechanical properties. Though stainless steel has 20% less load capacity and is slightly softer than our standard 52100 chromium steel used in most of our bearings, stainless steel is an excellent alternative for use in wet conditions, if you wash your bike often, or where sweat can be a problem. Enduro Bearings also uses LLB type seals and CRC Marine grease in these bearings to additionally water proof against the elements. Enduro 440C stainless headset bearings are the same bearings found in many popular headset brands, including those that carry a 110 year warranty.The Enduro line of angular-contact headset bearings start with Black Oxide treated Chromium Steel races, steps up to full 440C stainless steel, and the top of the line is, lifetime-guaranteed, XD-15 aerospace-stainless (races and balls). They are always engineered with the largest balls possible, feature dual-lip seals riding in a micro-groove (labyrinth) and are filled 90% with high pressure water proof grease for the ultimate protection against sweat and the elements. Enduro Angular Contact (A/C) bearings are designed so all balls are evenly engaged to spread the force over a larger surface area, minimizing wear and maximizing life.
ACB 4545 405495 SS 1-1/2" 440C stainless steel Angular Contact Headset bearing (40.5mm x 49.5mm x 6.5mm: 45x45 deg)
Angular-contact headset bearing featuring 440C stainless steel balls and races for superior corrosion protection.
This size bearings also known in the bike Industry by part number:
HSS 6011
ACB495H6.5
Static load - 470lbf / 2.09kN
Weight - 24g
Angular contact bearings provide maximum load distribution across all of the ball bearings unlike standard bearings which load only those at the bottom of the bearing. This load distribution ensures bearing life is increased drastically allowing for more time spent in the saddle than the workshop.
Bearing Code: ACB 3645 3544
Dimensions: 35 x 44 x 5.5mm
Angular Contacts: 36x45
ABEC: 3
Grade: 10
Grease: Kyodo Yushi PS-2
Application: Headsets
Weight: 25.50g
Angular contact bearings provide maximum load distribution across all of the ball bearings unlike standard bearings which load only those at the bottom of the bearing. This load distribution ensures bearing life is increased drastically allowing for more time spent in the saddle than the workshop.
Bearing Code: ACB 3645 3344
Dimensions: 33 x 44 x 6mm
Angular Contacts: 36x45
ABEC: 3
Grade: 10
Grease: Kyodo Yushi PS-2
Application: Headsets
Weight: 25.50g
1-3/8_ Angular Contact Bearing for Internal Headset featuring anti-corrosion Black Oxide/Magnetite coating of 52100 High-Carbon Chromium alloy races paired with grade 10 Balls. The Enduro line of headset bearings begin with chromium steel, Black Oxide finish A/C type and then offer full 440C stainless steel at the top. They are always engineered with the largest balls possible and dual lip seals riding in a micro groove for ultimate protection against sweat and the elements. They are filled 90% with high pressure waterproof grease, so you never have to guess if there is grease inside. In Angular Contact (A/C) bearings, ALL balls are engaged and spread the force over a larger surface area, to decrease friction and minimize wear.
Bearing Code: 6806 CC BO
Dimensions: 37 x 49 x 6.5mm
ABEC: 3Â
Grade: 10
Seals: LLB
Grease: Kyodo Yushi PS-2
Application: Headsets
Weight: 25.25g
The 40-Series is the work-horse of Cane Creek's headset line-up. The series incorporates all the features necessary for a durable, light-weight, long-lasting headset and represents the perfect balance of performance, durability and value. Suitable for any type of bike including road, gravel MTB.The new ZN40 bearings are a zinc-coated, machined steel cartridge bearing with hardened steel balls. The new material is much more corrosion-resistant, which vastly increases the longevity of the 40 series headsets.
Machined from 6061 T-6 Aluminium
Innovative Clip-Seal completely seals the top assembly and captures the compression ring to reduce the numberof loose parts
High quality, low friction face-seals
Durable steel crown race
Dependable ZN40, sealed bearings
Interlock spacer compatible
Upper/Lower stack: 16/12mm
Colour: Black
Weight: 156g
Warranty: 1 Year (excluding bearings)
Precision, quality, valueHellbender 70 Lite is a headset that packs durability, weight savings and value into one product. Equipped with 6000 series aluminum and 35% lighter over comparable models. The Hellbender 70 Lite is an ideal headset choice for any bike where weight savings is a priority - a lightweight headset that doesn’t lack durability or performance.
CUPS & COVERS: 6061 T-6 Aluminum Internally contoured and relieved to minimize weight and maximize strength
TOP COVER: Low-friction upper bearing seal completely seals cup from contaminants and is fully captured by the top cover with no loose parts
CROWN RACE: Alloy Dual-Seal crown race provides excellent seal efficiency
COMPRESSION RING:Â Low friction Carbon friendly captured compression ring
BEARINGS: Lightweight aluminum/w steel hybrid Hellbender LITE sealed cartridge bearing
WEIGHT: ZeroStack (ZS) — 90g (vs 117g for normal ZS Hellbender) Integrated (IS) — 54g (vs 81g for normal IS Hellbender)
Featuring some of the lowest stack height bearing cover options available, our premium stainless steel Hellbender bearing, 6061 T-6 Aluminum cups and covers, the Hellbender 70 Slam is a premium headset created for riders seeking to lower their handlebars as low as possible without compromising bearing longevity and proper preload.
CUPS & COVERS: 6061 T-6 Aluminum Internally contoured and relieved to minimize weight and maximize strength
TOP COVER: Designed with the lowest stack height possible for both ZS and IS headsets
CROWN RACE: Alloy Dual-Seal crown race provides excellent seal efficiency
COMPRESSION RING:Â Low friction Carbon friendly captured compression ring
BEARINGS: Premium sealed HELLBENDER stainless bearings
STACK HEIGHT: ZS - 2mm top (vs 8mm top for normal ZS Hellbender) IS - 4.6mm top (vs 9mm top for normal ZS Hellbender)
Angular contact bearings provide maximum load distribution across all of the ball bearings unlike standard bearings which load only those at the bottom of the bearing. This load distribution ensures bearing life is increased drastically allowing for more time spent in the saddle than the workshop.
Bearing Code: ACB 6805
Dimensions: 27,15 x 38 x 6,5mm
Angular Contacts: 36x45
ABEC: 3
Grade: 10
Grease: Kyodo Yushi PS-2
Application: Headsets
Angular contact bearings provide maximum load distribution across all of the ball bearings unlike standard bearings which load only those at the bottom of the bearing. This load distribution ensures bearing life is increased drastically allowing for more time spent in the saddle than the workshop.
Bearing Code: ACB 1125
Dimensions: 30,5 x 41,8 x 6,3mm
Angular Contacts: 36x45
ABEC: 3
Grade: 10
Grease: Kyodo Yushi PS-2
Application: Headsets
The 40-Series is the work-horse of Cane Creek's headset line-up. The series incorporates all the features necessary for a durable, light-weight, long-lasting headset and represents the perfect balance of performance, durability and value. Suitable for any type of bike including road, gravel MTB.The new ZN40 bearings are a zinc-coated, machined steel cartridge bearing with hardened steel balls. The new material is much more corrosion-resistant, which vastly increases the longevity of the 40 series headsets
Machined from 6061 T-6 Aluminium
Innovative Clip-Seal completely seals the top assembly and captures the compression ring to reduce the numberof loose parts
High quality, low friction face-seals
Durable steel crown race
Dependable ZN40, sealed bearings
Interlock spacer compatible
Upper/Lower stack: 9/1mm
Colour: Black
Weight: 92g
Warranty: 1 Year (excluding bearings)
Note: Tall/Wide Cover version fits specific Yeti frames - 2019 + SB150 / SB165 or anything else that requires the 51.5mm cover.
The 40-Series is the work-horse of Cane Creek's headset line-up. The series incorporates all the features necessary for a durable, light-weight, long-lasting headset and represents the perfect balance of performance, durability and value. Suitable for any type of bike including road, gravel MTB.The new ZN40 bearings are a zinc-coated, machined steel cartridge bearing with hardened steel balls. The new material is much more corrosion-resistant, which vastly increases the longevity of the 40 series headsets
Machined from 6061 T-6 Aluminium
Innovative Clip-Seal completely seals the top assembly and captures the compression ring to reduce the numberof loose parts
High quality, low friction face-seals
Durable steel crown race
Dependable ZN40, sealed bearings
Interlock spacer compatible
Upper/Lower stack: 9/1mm
Colour: Black
Weight: 71gÂ
Warranty: 1 Year (excluding bearings)
The 40-Series is the work-horse of Cane Creek's headset line-up. The series incorporates all the features necessary for a durable, light-weight, long-lasting headset and represents the perfect balance of performance, durability and value. Suitable for any type of bike including road, gravel MTB.The new ZN40 bearings are a zinc-coated, machined steel cartridge bearing with hardened steel balls. The new material is much more corrosion-resistant, which vastly increases the longevity of the 40 series headsets
Machined from 6061 T-6 Aluminium
Innovative Clip-Seal completely seals the top assembly and captures the compression ring to reduce the numberof loose parts
High quality, low friction face-seals
Durable steel crown race
Dependable ZN40, sealed bearings
Interlock spacer compatible
Upper/Lower stack: 8/4mm
Colour: Black
Weight: 88g
Warranty: 1 Year (excluding bearings)
Cane Creek’s engineers were tasked with developing a no-compromise, best-in-class premium headset. With the 110-Series, they did just that — using optimal materials, engineering the most effective internals and designing the best aesthetics available in a headset. The 110-Series offers the widest array of configurations available in a premium headset and all backed up with our new 100% Lifeime Warranty!
7075 T-6 Aluminum, Internally contoured and relieved to minimize weight and maximize strength
A captured compression ring sets the bearing preload and stays true no matter how you ride (no rocking or creaking)Â
Premium split-lip sealed Hellbender stainless steel bearings give double the protection while decreasing friction
Compatible with Interlock spacers
Hand polished and anodised
Upper/Lower stack: 16/12mm
Weight: 97g
